Search Results

A new generation of highly downsized SI engines with specific power output around or above 150 HP/liter is emerging in the sport car market sector. Technologies such as high-boosting, direct injection and downsizing are adopted to increase power density and reduce fuel consumption. To counterbalance the increased risks of pre-ignition, knock or mega-knock, currently made turbocharged SI engines usually operate with high fuel enrichments and delayed (sometimes negative) spark advances. The former is responsible for high fuel consumption levels, while the latter induce an even lower A/F ratio (below 11), to limit the turbine inlet temperature, with huge negative effects on BSFC. A possible solution to increase knock resistance is investigated in the paper by means of 3D-CFD analyses: water/methanol emulsion is port-fuel injected to replace mixture enrichment while preserving, if not improving, indicated mean effective pressure and knock safety margins.

Engine downsizing is gaining popularity in the high performance engine market sector, where a new generation of highly downsized engines with specific power outputs around or above 150 HP/litre is emerging. High-boost and downsizing, adopted to increase power density and reduce fuel consumption, have to face the increased risks of pre-ignition, knock or mega-knock. To counterbalance autoignition of fuel/air mixture, such engines usually operate with high fuel enrichments and delayed (sometimes negative) spark advances. The former is responsible for high fuel consumption levels, while the latter reduces performance and induces an even lower A/F ratio (below 11), to limit the turbine inlet temperature, with huge negative effects on BSFC.

In order to improve fuel conversion efficiency, currently made spark-ignited engines are characterized by the adoption of gasoline direct injection, supercharging and/or turbocharging, complex variable valve actuation strategies. The resulting increase in power/size ratios is responsible for substantially higher average thermal loads on the engine components, which in turn result in increased risks of both thermo-mechanical failures and abnormal combustion events such as surface ignition or knock. The paper presents a comprehensive numerical methodology for the accurate estimation of knock tendency of SI engines, based on the integration of different modeling frameworks and tools. Full-cycle in-cylinder analyses are used to estimate the point-wise heat flux acting on the engine components facing the combustion chamber.

Enhanced calibration strategies and innovative engine combustion technologies are required to meet the new limits on exhaust gas emissions enforced in the field of marine propulsion and on-board energy production. The goal of the paper is to optimize the control parameters of a 4.2 dm3 unit displacement marine DI Diesel engine, in order to enhance the efficiency of the combustion system and reduce engine out emissions. The investigation is carried out by means of experimental tests and CFD simulations. For a better control of the testing conditions, the experimental activity is performed on a single cylinder prototype, while the engine test bench is specifically designed to simulate different levels of boosting. The numerical investigations are carried out using a set of different CFD tools: GT-Power for the engine cycle analysis, STAR-CD for the study of the in-cylinder flow, and a customized version of the KIVA-3V code for combustion.

The paper reports the application of Proper Orthogonal Decomposition (POD) to LES calculations for the analysis of combustion and knock tendency in a highly downsized turbocharged GDI engine that is currently under production. In order to qualitatively match the cyclic variability of the combustion process, Large-Eddy Simulation (LES) of the closed-valve portion of the cycle is used with cycle-dependent initial conditions from a previous multi-cycle analysis [1, 2, 3]. Detailed chemical modelling of fuel's auto-ignition quality is considered through an ad-hoc implemented look-up table approach, as a trade-off between the need for a reasonable representation of the chemistry and that of limiting the computational cost of the LES simulations. Experimental tests were conducted operating the engine at knock-limited spark advance (KLSA) and the proposed knock model was previously validated for such engine setup [3].

The paper describes an integrated methodology for the accurate characterization of the thermal behavior of internal combustion engines, with particular reference to a high performance direct injected SI engine for sport car applications. The engine is operated at full load and maximum power revving speed, which is known to be critical from the point of view of thermal stresses on the engine components. In particular, two different sets of 3D-CFD calculations are adopted: on one side, full-cycle in-cylinder analyses are carried out to estimate the point wise thermal heat flux due to combustion on the engine components facing the combustion chamber. On the other side, full-engine multi-region CHT calculations covering the engine coolant jacket and the surrounding metal components are used to compute the point wise temperature distribution within the engine head, liner and block.

The paper reports the application of LES multi-cycle analysis for the characterization of cycle to cycle variability (hereafter CCV) of a highly downsized DISI engine for sport car applications. The analysis covers several subsequent engine cycles operating the engine at full load, peak power engine speed. Despite the chosen engine operation is usually considered relatively stable, relevant fluctuations were experimentally measured in terms of in-cylinder pressure evolution and combustion phasing. On one hand, despite the complex architecture of the V-8 engine, the origin of such CCV is considered to be poorly related to cyclic fluctuations of the gas-dynamics within the intake and exhaust pipes, since acquisitions of the instantaneous pressure traces at both the intake port entrance and exhaust port junction by fast-response pressure measurements over 250 subsequent engine cycles showed almost negligible differences in both amplitude and phasing compared to those within the cylinder.

The paper investigates the idle operating condition of a current production turbocharged Gasoline Direct Injected (GDI) high performance engine both from an experimental and a numerical perspective. Due to the low engine speed, to the low injection pressure and to the null contribution of the turbocharger, the engine condition is far from the standard points of investigation. According to the low heat flux due to combustion, temperature levels are low and reduced fuel evaporation is expected. Consequently, fuel spray evolution within the combustion chamber and spray/wall interaction are key points for the understanding of the combustion process. In order to properly investigate and understand the many complex phenomena, a wide set of engine speeds was experimentally investigated and, as far as the understanding of the physics of spray/wall interaction is concerned, many different injection strategies are tested.

The paper presents a combined experimental and numerical activity carried out to improve the accuracy of conjugate heat transfer CFD simulations of a high-performance S.I. engine water cooling jacket. Due to the complexity of the computational domain, which covers both the coolant jacket and the surrounding metal cast (both head and block), particular care is required in order to find a tradeoff between the accuracy and the cost-effectiveness of the numerical procedure. In view of the presence of many complex physical phenomena, the contribution of some relevant CFD parameters and sub-models is separately evaluated and discussed. Among the formers, the extent of the computational domain, the choice of a proper set of boundary conditions and the detailed representation of the physical properties of the involved materials are separately considered.

The paper investigates the low-temperature cranking operation of a current production automotive Gasoline Direct Injected (GDI) by means of 3D-CFD simulations. Particular care is devoted to the analysis of the hollow cone spray evolution within the combustion chamber and to the formation of fuel film deposits on the combustion chamber walls. Due to the high injected fuel amount and the strongly reduced fuel vaporization, wall wetting is a critical issue and plays a fundamental role on both the early combustion stages and the amount of unburnt hydrocarbons formation. In fact, it is commonly recognized that most of the unburnt hydrocarbon emissions from 4-stroke gasoline engines occur during cold start operations, when fuel film in the cylinder vaporize slowly and fuel can persist until the exhaust stroke.

The paper presents a numerical activity directed at the analysis and optimization of internal combustion engine water cooling jackets, with particular emphasis on the fatigue-strength assessment and improvement. In the paper, full 3D-CFD and FEM analyses of conjugate heat transfer and load cycle under actual engine operation of a single bank of a current production V6 turbocharged diesel engine are reported. A highly detailed model of the engine, made up of both the coolant galleries and the surrounding metal components, i.e., the engine head, the engine block, the gasket, the valve guides and valve seats, is used on both sides of the simulation process to accurately capture the influence of the cooling system layout under thermal and load conditions as close as possible to actual engine operations.

The paper aims at providing information about the influence of the combustion chamber shape on the combustion process evolution in a high speed direct injection (HSDI) small unit displacement engine for off-highway applications. Small HSDI Diesel engines require a deep optimisation process in order to maximize specific power output, while limiting pollutant emissions without additional expensive pollutant aftertreatment equipments. Making reference to a current production engine, the purpose of this paper is to investigate the influence of combustion chamber design on both engine performances and combustion efficiency. The actual piston omega-shape is progressively distorted in order to assess the influence of some of the main bowl-features on both mean-flow evolution, mixture formation and pollutants.

The paper aims at providing information about the in-cylinder flow structure and its evolution of a high speed direct injection (HSDI) four valve per cylinder engine for off-highway applications. Fully transient CFD analyses by means of state-of-the-art tools and methodologies are carried out for the whole intake and compression strokes, in order to evaluate port effects on both engine permability and in-cylinder flow field evolution. Organized mean motions (i.e., swirl, tumble and squish) are investigated, trying to establish general rules in the port design optimization process, addressing relationships between the relative port orientation and the in-cylinder flow structure. Different port configurations are compared, each deriving from the rotation of the BASE port configuration on two different planes, the former being perpendicular to the cylinder axis, while the latter being parallel to the cylinder axis.